Submersible Wastewater Pump

Submersible Wastewater Pump
Product Introduction:
A professional submersible wastewater pump represents a sophisticated fusion of hydraulic fluid mechanics and underwater electrical isolation engineering. In severe municipal collection wells and aggressive industrial effluent sumps, mechanical integrity cannot rely on standard consumer-grade pump architecture.
Send Inquiry
Description
Technical Parameters

Hebei Dehuike Pump Industry Co., Ltd. is one of the most reliable manufacturers and suppliers of submersible wastewater pump in China. With abundant experience, we are committed to providing high quality customized pumps with competitive price. Welcome to wholesale bulk submersible wastewater pump for sale here from our factory. Also, pricelist is available.

 

Product Detail & Structural Anatomy

 

A professional submersible wastewater pump represents a sophisticated fusion of hydraulic fluid mechanics and underwater electrical isolation engineering. In severe municipal collection wells and aggressive industrial effluent sumps, mechanical integrity cannot rely on standard consumer-grade pump architecture. Each heavy-duty submersible wastewater pump is constructed from high-tensile pearlitic grey cast iron HT200 or HT250, exhibiting a minimum tensile strength of 200 to 250 MPa to withstand extreme hydrodynamic impact loads and continuous submerged hydrostatic pressure.

The structural anatomy of the submersible wastewater pump centers on a dynamic balance between heavy casting mass and optimized fluid passage volume. The pump casing incorporates an enlarged volute chamber characterized by smooth hydraulic curvature, eliminating sudden cross-sectional transitions where slurry solids, stringy rags, and settling grit typically accumulate. Depending on target fluid abrasiveness, the wetted volute wall thickness is reinforced to 18–35 mm, providing a substantial wear allowance that ensures structural longevity even in abrasive wastewater containing up to 2% suspended mineral particles.

product-800-800

Core Component Breakdown & Metallurgy:

  • Precision Impeller Geometry: The non-clogging impeller is cast in high-grade ductile iron QT500-7 or wear-resistant chrome alloy white iron. Dynamic hydraulic balancing to ISO 1940 Grade G2.5 ensures residual vibration remains below 2.8 mm/s RMS, protecting bearings from premature fatigue under fluctuating flow conditions.
  • Rigid Drive Shaft Construction: The heavy-duty pump shaft is machined from high-yield 2Cr13 martensitic stainless steel or heat-treated 40Cr alloy steel. A stepped-diameter shaft profile minimizes shaft deflection at the mechanical seal faces to less than 0.05 mm, ensuring consistent face parallelity under severe hydraulic shock loads.
  • Submersible Motor Shell & End Shields: The motor operates inside a hermetically sealed pressure vessel enclosure rated to IP68 enclosure protection. Cast iron end bells and stator housing joints feature precision CNC-machined spigots fitted with twin fluororubber (FKM) or nitrile (NBR) O-rings, providing dual-redundant fluid barrier integrity up to 20 meters static submersion depth.
  • Dual-Barrier Mechanical Seal Chamber: Tandem tungsten carbide (TC) versus silicon carbide (SiC) mechanical seals operate within an independent oil bath. The intermediate oil chamber not only lubricates the friction faces continuously but also acts as a thermal dissipation buffer, preventing dry-run catastrophic failure if suction liquid levels temporarily drop.
  • Hermetic Cable Gland Isolation: The electrical power line uses heavy-gauge ethylene propylene rubber (EPR) insulated, chloroprene rubber sheathed submersible flexible cable. The cable entry gland features a conical mechanical compression ring combined with solid polyurethane resin potting, completely eliminating capillary water seepage along copper conductor strands.

Every structural fastener utilized on the exterior wet surfaces of the submersible wastewater pump is fabricated from Grade 304 or Grade 316 austenitic stainless steel. Flanged discharge connections conform strictly to ISO 7005-2 and EN 1092-2 PN10/PN16 dimensional standards, allowing seamless bolt-up integration with global piping networks without requiring customized flange adapters or on-site welding modifications.

 

Production Process & Precision Manufacturing

 

Engineering excellence in submersible wastewater pump manufacturing depends strictly upon systematic quality control at every metallurgical, machining, and assembly checkpoint. Hebei Dehuike Pump Industry Co., Ltd. operates a vertically integrated production workflow spanning over 8,000 square meters of specialized manufacturing facilities, ensuring that each production milestone adheres to rigorous international engineering standards.

■ Step 1: Metallurgical Casting & Sand Molding

The manufacturing process begins in the specialized foundry division utilizing resin-bonded sand molding technology. Electric induction furnaces melt high-purity pig iron and selected structural scrap under continuous spectral optical emission spectrometry analysis. Carbon equivalent, silicon ratio, and manganese content are strictly regulated to eliminate chill microstructures and internal gas porosity. Castings undergo controlled natural cooling followed by thermal stress-relief annealing at 550°C to eliminate residual casting stresses before precision metal cutting.

■ Step 2: Precision CNC Machining & Tolerance Control

Annealed volute casings, motor shells, bearing brackets, and discharge elbows are transferred to the heavy machining shop equipped with large-scale computer numerical control (CNC) horizontal and vertical machining centers. Critical bearing journals, mechanical seal cavities, and pilot spigots are single-setup machined to IT6 and IT7 dimensional tolerance grades. Concentricity and perpendicularity between the upper and lower bearing bores are held within 0.015 mm, guaranteeing absolute alignment throughout the high-torque rotating assembly.

■ Step 3: Stator Winding, VPI Insulation & Motor Assembly

The submersible electric motor stator is wound with high-conductivity electrolytic copper wire insulated with Class F or Class H enamels. After automated automated coil insertion, the entire wound stator core undergoes Vacuum Pressure Impregnation (VPI) with solvent-free polyester resin. This process thoroughly fills all microscopic winding voids, imparting superior dielectric resistance, exceptional thermal conductivity to the outer casing, and absolute immunity to moisture degradation under thermal cyclic stress.

■ Step 4: Dynamic Impeller Balancing & Shaft Alignment

Each cast impeller is CNC contour-machined to ensure precise hydrodynamic vane profiles matching original CAD/CFD fluid models. Finished impellers are individually mounted onto dedicated balancing mandrels and evaluated on automated dynamic balancing stations. Precision material trimming from the outer shroud brings residual dynamic unbalance down to ISO 1940 Grade G2.5 limits. Pump shafts are 100% inspected on precision optical runout testers to ensure total radial runout remains under 0.02 mm across the entire bearing span.

■ Step 5: Cleanroom Assembly & Dual Hydrostatic Testing

Final unit assembly takes place in a dedicated clean assembly zone to prevent airborne grit from contaminating mechanical seal faces and high-precision deep-groove ball bearings. Following complete mechanical assembly, the motor housing and intermediate oil chamber undergo a 0.2 MPa dry nitrogen pressure decay leak test for 30 minutes, followed by a 0.4 MPa hydrostatic pressure integrity test on the pump casing, ensuring zero fluid penetration under deep submergence.

 

Experience and Global Markets

 

With more than 30 years of continuous manufacturing and fluid engineering experience, Hebei Dehuike Pump Industry Co., Ltd. has established an enduring track record as a trusted supplier of industrial fluid transfer machinery. The company's heavy-duty submersible wastewater pump units operate in municipal infrastructures, private mining operations, power plants, and agricultural reclamation networks across more than 50 countries worldwide.

Global Project Deployment Portfolio:

  • Philippines Municipal Drainage: Supplied municipal lift stations and water reclamation facilities in Southeast Asia, including high-capacity 200–350 mm submersible wastewater pump installations operating continuously in Manila and Cebu wet collection basins during monsoon seasons.
  • North American Industrial Process: Delivered robust industrial end-suction and high-flow submersible wastewater pump units to process facilities across Texas and California, engineered to local 460V/60Hz electrical grid specifications with full NEMA-compatible wiring standards.
  • South Korean Industrial Manufacturing: Engineered severe-duty vertical and submersible wastewater pumping systems for industrial chemical complexes, processing aggressive wastewater containing abrasive particulates and complex organic effluents.
  • African Resource Extraction & Mine Dewatering: Provided heavy-duty submersible wastewater and hydraulic slurry pumping packages to remote open-pit mining operations, handling pit sump dewatering, tailings decant transfer, and seasonal flood containment under extreme ambient temperatures.

Through decades of international field exposure, our engineering staff has developed deep domain knowledge regarding differing national water treatment philosophies, grid voltage variations (e.g., 208V, 220V, 380V, 415V, 440V, 460V, 690V at 50Hz and 60Hz), and regional environmental regulations. Our engineering database houses field telemetry data from hundreds of operational sites, enabling rapid, risk-free model configuration for new international engineering contractors.

product-800-800

 

Our Service & Engineering Support

 

Procuring industrial pumping machinery is an engineering partnership that extends far beyond product delivery. Hebei Dehuike Pump Industry Co., Ltd. provides a comprehensive technical service architecture covering every project lifecycle stage - from initial hydrological feasibility studies to long-term operational maintenance optimization.

■ Pre-Engineering Hydraulic Modeling & System Head Verification

Selecting an optimal submersible wastewater pump requires rigorous analysis of static elevation differences, dynamic piping friction losses, minor fitting resistance coefficients, and fluid rheology. Our engineering department uses specialized hydraulic calculation software to plot the system head loss curve against the pump H-Q characteristic curve. This ensures the selected duty point falls strictly within the pump's Preferred Operating Region (POR) between 70% and 115% of Best Efficiency Point (BEP), preventing cavitation, shaft deflection, and excessive motor loading.

■ Custom Metallurgical & Electrical Tailoring

Every wastewater application presents unique chemical and electrical parameters. We offer custom electrical engineering including dual-voltage motor windings, PTC thermistor temperature sensor integration, PT100 bearing temperature detectors, and float-switch automated level control panels. For aggressive media, wetted components can be configured in cast 304, 316, or 316L stainless steel, duplex stainless steel 2205, or treated with ceramic-reinforced wear-resistant polymer coatings.

■ Comprehensive CAD / BIM Engineering Submittal Packages

To streamline mechanical consulting and civil engineering integration, our technical support desk furnishes full submittal document packages within 24–48 hours of project consultation. These include certified dimensional outline drawings, AutoCAD .DWG files, 3D STEP solid models, complete electrical connection schematics, and factory-verified performance curves detailing Flow, Head, Shaft Power, and Hydraulic Efficiency across the complete operating envelope.

■ After-Sales Commissioning Guidance & Rapid Spare Parts Supply

Our technical team provides detailed multilingual installation manuals, video commissioning walk-throughs, and remote tele-engineering support for site electrical contractors. Supported by a 900+ vendor supply chain ecosystem, we maintain dedicated inventory of factory-original replacement wear parts - including mechanical seal kits, precision bearings, matched O-ring gaskets, and spare impellers - dispatched worldwide to guarantee minimal operational interruption.

product-800-800

 

Packaging & International Logistics

 

International transport of heavy electromechanical equipment requires specialized export packaging to prevent mechanical shock, vibration damage, and marine atmospheric corrosion during ocean transit. Hebei Dehuike Pump Industry Co., Ltd. implements standardized, rigorous export preservation and shipping protocols for every submersible wastewater pump leaving our manufacturing facility.

■ Multi-Layer Corrosion Inhibition & Vapor Barrier Packaging

Prior to crating, all external unpainted machined surfaces - including discharge flanges, shaft extensions, and guide rail mounting brackets - are coated with heavy-duty wax-based rust preventative compounds. The electrical cable is neatly coiled and secured to prevent kink stresses, and the cable termination is hermetically sealed within heavy vulcanized waterproof sleeves. The entire submersible wastewater pump assembly is wrapped in heavy-duty polyethylene vapor corrosion inhibitor (VCI) film containing desiccant packs, isolating the machinery from salty ocean air and humidity shifts.

■ Solid Timber Crating & Structural Internal Bracing

Pumps are housed inside heavy-duty custom export wooden crates manufactured strictly from heat-treated, fumigated timber conforming to international ISPM 15 phytosanitary regulations. Internal structural timber saddles, contour-cut to the pump volute and motor body, are bolted to the crate framework to eliminate all shifting and shock loads during container handling. Heavy units (weights exceeding 500 kg) are anchored with high-tensile steel banding to heavy forklift-compatible skids featuring four-way entry for secure crane and forklift maneuvering.

■ Export Shipping Modes & Incoterms Policy

To accommodate diverse project schedules and consignment volumes, our logistics department operates two standardized international transport routes: Air Freight for urgent spares and lightweight pump consignments ranging from 50 to 500 kg, and Ocean Freight (FCL full container load or LCL consolidated cargo) for heavy machinery shipments exceeding 500 kg. All export quotations are issued strictly on transparent FOB or CIF destination port terms, ensuring complete clarity for international customs clearance and port terminal handling.

product-800-800

 

Equipment Inspection & Factory Testing

 

High reliability in submerged municipal service is impossible without uncompromising manufacturing and testing infrastructure. The Dehuike production plant houses an extensive fleet of modern machine tools and advanced hydraulic test systems dedicated to ensuring total product compliance before dispatch.

Advanced Manufacturing Machine Tool Infrastructure:

  • Heavy CNC Turning Centers: Equipped with precision CNC horizontal lathe beds capable of swinging workpieces up to 1.6 meters diameter, ensuring microscopic dimensional repeatability on large-diameter submersible wastewater pump casings.
  • Precision Vertical Machining Centers: Multi-axis computer numerical control vertical machining centers deliver simultaneous five-face milling and precision drilling on motor end shields, volute casings, and auto-coupling discharge brackets.
  • Automated Dynamic Rotor Balancers: Microprocessor-controlled dynamic balancing machines evaluate rotating impellers and complete rotor assemblies at operating rotational speeds, detecting unbalance down to fractions of a gram-millimeter.
  • Hydraulic Assembly Pressing Workstations: Custom-built hydraulic pressing fixtures and hydraulic expansion mandrels ensure controlled, stress-free insertion of precision ball bearings and mechanical seal assemblies without impact damage.
product-800-800

■ Full-Scale Precision Hydraulic Test Bench Facility

The cornerstone of our quality assurance infrastructure is our computerized closed-loop hydraulic testing station, featuring a subterranean deep-water testing sump with water capacity exceeding 1,200 cubic meters. Calibrated electromagnetic flow meters, high-precision digital pressure transmitters, and digital torque-frequency power analyzers record real-time operating metrics at 1-second intervals. Testing strictly adheres to ISO 9906 Grade 2B and Grade 1B acceptance standards, verifying flow rate, total head, absorbed electrical power, overall efficiency, and NPSH across a minimum of seven distinct operating points along the performance curve.

■ Non-Destructive Testing (NDT) & Metallurgical Quality Checks

Castings subject to heavy hydraulic pressure undergo ultrasonic wall thickness measurement and magnetic particle flaw detection to ensure zero subsurface casting cracks or shrinkage cavities. In addition, electrical insulation is validated through automated megger insulation testing at 1,000V DC and high-potential dielectric breakdown testing at 2,000V AC for 60 seconds, ensuring flawless electrical isolation under continuous full-load submerged duty.

 

International Certification & Compliance

 

product-793-540

 

When international municipal bodies and engineering conglomerates tender for critical infrastructure equipment, third-party verified conformity certifications represent an essential prerequisite for procurement qualification. Hebei Dehuike Pump Industry Co., Ltd. operates in full compliance with recognized global industrial standards.

■ ISO 9001:2015 Quality Management System Certification

Our manufacturing facility operates under an independently audited ISO 9001:2015 quality management framework. From raw metallurgical procurement and vendor audit management to CNC tool calibration, in-process routing, and final hydrodynamic testing, every manufacturing step is governed by standardized operating procedures (SOP). Full batch traceability documentation is maintained for a minimum of ten years, providing long-term audit reliability for major civil engineering contractors and municipal utility authorities.

■ EAC Conformity Certificate (Eurasian Customs Union)

The entire WQ submersible wastewater pump series holds valid EAC (Eurasian Conformity) certification, validating compliance with Technical Regulations of the Customs Union including TR CU 010/2011 (Safety of Machinery and Equipment), TR CU 004/2011 (Safety of Low Voltage Equipment), and TR CU 020/2011 (Electromagnetic Compatibility of Technical Means). This allows streamlined, tariff-compliant importation and installation across all Eurasian Economic Union member states.

■ RoHS Environmental Directive Compliance

All materials, seal components, electrical cabling, and internal insulating resins utilized in the submersible wastewater pump conform strictly to the European Union RoHS (Restriction of Hazardous Substances) Directive 2011/65/EU and its amendment (EU) 2015/863. Lead, mercury, cadmium, hexavalent chromium, and restricted phthalate plasticizers are strictly monitored, ensuring safe environmental discharge into municipal sewage ecosystems without secondary contamination.

■ Factory Warranty Commitment

Demonstrating our uncompromised confidence in manufacturing precision and material durability, Hebei Dehuike Pump Industry Co., Ltd. provides a comprehensive 24-month (2-year) factory warranty covering the entire submersible wastewater pump unit (excluding normal consumable wear parts such as mechanical seal faces, O-rings, and sacrificial impeller wear bands). In the rare event of a verified manufacturing defect, replacement components are dispatched immediately under our global rapid warranty fulfillment protocol.

 

Technical Selection Guide & Inquiry Format

 

product-800-344

 

To assist consulting engineers, municipal procurement directors, and mechanical contractors in accurately sizing and selecting the optimal submersible wastewater pump, the following engineering reference table presents verified performance data from representative production models across our medium-to-large capacity series.

Representative High-Performance Duty Models (Rated Point):

Type

Flow Q
(m³/h)

Head H
(m)

Speed n
(r/min)

Shaft power P
(kW)

Mating motor
(kW)

Weight
(kg)

Overall dimensions
LxWxH (mm)

Caliber (mm)

Inlet

Outlet

40WQ12-15-1.5

8.4

16

2900

0.89

1.5

55

330×205×506

-

40

12

15

1.02

14.4

14

1.17

50WQ10-10-0.75

7

11.5

2900

0.45

0.75

45

286×198×550

-

50

10

10

0.5

12

8

0.51

50WQ15-15-1.5

10.5

16.5

2900

1.12

1.5

55

291×205×550

-

50

15

15

1.2

18

14

1.37

50WQ15-20-2.2

10.5

22.5

2900

1.5

2.2

60

315×225×605

-

50

15

20

1.6

18

17.3

1.67

50WQ17-25-3

11.9

26

2900

1.9

3

70

390×280×660

-

50

17

25

2.1

20.4

23.8

2.14

50WQ18-15-1.5

12.6

16.5

2900

1.06

1.5

60

295×228×610

-

50

18

15

1.19

21.6

14

1.29

50WQ20-7-0.75

14

7.8

2900

0.56

0.75

50

361×260×580

-

50

20

7

0.62

24

6.2

0.66

50WQ24-20-14

16.8

25

2900

1.97

4

130

520×400×740

-

50

24

20

1.95

28.8

17.3

2.02

50WQ25-10-1.5

17.5

11.5

2900

1

1.5

60

300×225×605

-

50

25

10

1.02

30

8

1.01

50WQ27-15-2.2

18.9

16.5

2900

1.39

2.2

70

330×290×680

-

50

27

15

1.58

32.4

14

1.82

50WQ25-32-5.5

17.5

36

2900

4.05

5.5

105

420×295×800

-

50

25

32

4.35

30

27.5

4.45

50WQ40-15-4

28

16.5

2900

2.52

4

130

520×394×750

-

50

40

15

2.44

48

14

2.86

50WQ40-30-7.5

28

33

2900

4.94

7.5

180

540×420×870

-

50

40

30

5.27

48

26.5

5.78

50WQ42-9-2.2

29.4

10.5

2900

1.36

2.2

70

420×290×710

-

50

42

9

1.39

50.4

8

1.55

65WQ25-15-2.2

17.5

17.2

2900

1.8

2.2

60

333×215×610

-

65

25

15

1.9

30

13

1.95

65WQ25-28-24

17.5

30.2

2900

3.05

4

90

388×260×665

-

65

25

28

3.3

30

26

3.4

65WQ37-13-3

25.9

14.5

2900

1.97

3

80

388×270×710

-

65

37

13

2.18

44.4

11

2.29

80WQ29-8-2.2

20.3

9.5

2900

1.34

2.2

70

388×255×640

-

80

29

8

1.4

34.8

6.5

1.43

80WQ40-7-2.2

28

9.5

2900

1.47

2.2

70

390×260×640

-

80

40

7

1.55

48

5.7

1.58

80WQ40-15-4

28

17

2900

2.6

4

90

400×268×710

-

80

40

15

2.8

48

13.3

2.9

80WQ43-13-3

30.1

15.2

2900

2.15

3

80

390×260×600

-

80

43

13

2.35

51.6

9

2.4

80WQ50-10-3

35

11.5

2900

1.71

3

110

410×310×886

-

80

50

10

1.89

60

8

1.87

80WQ-50-25-7.5

35

27.5

2900

5.8

7.5

140

435×276×790

-

80

50

25

6

60

22.5

6

80WQ60-13-4

42

14.5

2900

2.59

4

130

520×390×750

-

80

60

13

2.95

72

11

3.08

100WQ50-22-7.5

35

23.5

1450

4.15

7.5

180

560×400×880

-

100

50

22

4.76

60

20

5.45

100WQ50-35-11

35

38.5

1450

6.8

11

260

605×450×960

-

100

50

35

7.69

60

31.7

8.63

100WQ65-15-5.5

45.5

17.5

1450

4.25

5.5

150

545×360×850

-

100

65

15

4.5

78

12

4.4

100WQ70-7-3

49

9.5

1450

1.98

3

110

410×315×860

-

100

70

7

1.78

84

5.7

1.92

100WQ70-22-11

49

23.5

1450

5.14

11

260

560×410×970

-

100

70

22

6

80

20.5

6.57

100WQ80-9-4

56

11

1450

3.05

4

130

565×370×770

-

100

80

9

3.2

96

7

3.21

100WQ80-20-7.5

56

22.5

1450

5.21

7.5

170

565×365×825

-

100

80

20

6.14

96

17

6.35

100WQ87-28-15

60.9

31

1450

8.72

15

300

560×410×970

-

100

87

28

9.62

104.4

25.3

10.74

100WQ100-7-4

70

9.4

1450

2.72

4

110

480×355×760

-

100

100

7

2.54

120

5.6

2.54

100WQ100-15-7.5

70

17.5

1450

5.65

7.5

165

565×365×855

-

100

100

15

5.9

120

12.5

6

100WQ100-22-15

70

23.3

1450

9

15

280

630×420×1050

-

100

100

22

9.5

120

20.5

10.5

100WQ110-10-5.5

77

11.5

1450

4

5.5

150

545×370×850

-

100

110

10

4.47

132

7

3.9

150WQ570-40-18.5

49

44.5

1450

12.92

18.5

520

700×480×1080

-

150

70

40

14.13

84

36

15.85

150WQ100-40-30

70

44.5

1450

16.32

30

820

820×680×1185

-

150

100

40

18.17

120

36

20.29

150WQ110-15-7.5

70

17.5

1450

5.74

7.5

260

460×395×965

-

150

110

15

6

132

12.5

6.24

100WQ130-30-22

91

35

1450

13.7

22

420

720×500×1060

-

150

130

30

15.5

156

24

16.2

150WQ140-7-5.5

98

8.5

1450

3.37

5.5

180

545×450×830

-

150

140

7

3.38

168

5.6

3.33

150WQ140-18-15

98

21

1450

8.62

15

300

575×460×1100

-

150

140

18

9.4

168

15

9.67

150WQ140-41-37

98

46

1450

22.75

37

1150

895×720×1800

-

150

140

41

24.83

168

31.5

27.85

150WQ145-9-7.5

101.5

11

1450

5.3

7.5

180

600×380×850

-

150

145

9

5.6

174

6.6

5.8

150WQ150-26-18.5

105

28.5

1450

13.7

18.5

400

710×495×1050

-

150

150

26

14.7

180

23.7

15.2

150WQ150-35-37

105

40

1450

20

37

760

940×640×1350

-

150

150

35

23

180

30

23

150WQ160-15-15

112

18

1450

8.5

15

300

710×455×900

-

150

160

15

9.7

192

12.6

10

150WQ180-22-18.5

126

25

1450

12.6

18.5

400

695×485×1050

-

150

180

22

14.6

216

19

15.5

150WQ200-10-15

140

11.5

1450

7.83

15

300

700×455×990

-

150

200

10

8.51

240

7

7.38

150WQ200-30-37

140

35

1450

22.2

37

750

960×640×1350

-

150

200

30

25.2

240

24

25.3

150WQ210-7-7.5

147

8.3

1450

7.62

7.5

180

540×440×910

-

150

210

7

5.01

252

5.5

4.84

150WQ250-22-30

175

23.5

1450

17.32

30

820

795×600×1200

-

150

250

22

20.39

300

19.8

21.87

200WQ250-11-15

175

13.2

1450

9.2

15

350

620×380×1050

-

200

250

11

10.2

300

9

10.8

200WQ250-15-18.5

175

17.7

1450

14

18.5

420

660×420×1050

-

200

250

15

14.7

300

13

15

200WQ250-22-30

175

24.8

1450

19

30

720

915×560×1120

-

200

250

22

21

300

19.5

22

200WQ250-35-45

175

41

1450

32.2

45

950

1060×760×1450

-

200

250

35

35

300

29.5

35

200WQ250-40-55

175

44.5

1450

36.59

55

1380

1180×1040×1950

-

200

250

40

38.38

300

35.7

41.69

200WQ300-7-11

110

8.2

1450

6.9

11

370

640×400×1050

-

200

300

7

7.6

360

5.9

8

200WQ310-13-22

117

16

1450

14.7

22

450

930×600×1060

-

200

310

13

15.5

372

11

16.6

200WQ350-20-37

245

22.5

1450

22.8

37

950

990×680×1840

-

200

350

20

24.5

420

17

25.9

200WQ350-25-37

245

27.8

1450

30

37

850

890×580×1160

-

200

350

25

32.5

420

22.7

33.8

200WQ350-40-75

245

44.5

1450

47.92

75

1750

1230×990×2100

-

200

350

40

51.83

420

35.5

57.23

200WQ360-15-30

250

17.5

1450

18.2

30

820

790×590×1250

-

200

360

15

18.89

432

12.6

19.78

200WQ400-7-15

280

8.3

1450

9.05

15

300

815×630×1120

-

200

400

7

9.3

480

5.7

9.44

200WQ400-10-22

280

12.6

1450

14

22

450

920×590×1060

-

200

400

10

14.8

480

8

15.1

200WQ400-13-30

280

16

1450

17.7

30

650

935×600×1120

-

200

400

13

18.6

480

11

20

200WQ400-25-45

280

28

1450

31.89

45

1280

1060×760×1950

-

200

400

25

35.16

480

22

38.37

200WQ400-30-55

280

35

1450

45

55

1300

1050×740×1550

-

200

400

30

46

480

27

46.5

250WQ600-9-30

420

10.5

980

17.2

30

850

1050×700×1650

-

250

600

9

18.9

720

7

19.8

250WQ600-12-37

420

14

1450

24.3

37

850

1050×700×1650

-

250

600

12

25.8

720

10

29.9

250WQ600-15-45

420

17

1450

31.3

45

950

1050×700×1650

-

250

600

15

33.6

720

13

41.2

250WQ600-20-55

420

22.5

1450

40.2

55

1300

1070×740×1680

-

250

600

20

44.8

720

17

63.9

250WQ600-25-75

420

27.53

1450

50

75

1500

1120×760×1750

-

250

600

25

54.5

720

21

66.6

250WQ600-30-90

420

35

1450

39.79

90

2000

1155×970×2120

-

250

600

30

62.88

720

27

69.7

250WQ700-11-37

490

13

1450

24.11

37

1150

980×680×1860

-

250

700

11

25.28

840

9

25.43

250WQ700-22-75

490

25

1450

48.3

75

1750

1165×820×1505

-

250

700

22

51.8

840

19

55.05

300WQ400-20-45

280

22.5

1450

26.8

45

1500

1110×900×1770

-

300

400

20

39.5

480

17

33.5

300WQ480-15-45

336

17.5

1450

24.3

45

1500

1110×900×1770

-

300

480

15

25.8

620

13

29.7

300WQ600-20-55

420

22.5

1450

40.9

55

1550

1110×900×1770

-

300

600

20

44.8

720

17

51.6

300WQ800-12-45

560

14

980

32.4

45

1550

1110×900×1770

-

300

800

12

35.4

960

10

36.8

300WQ800-15-55

560

17.5

980

37.09

55

1380

1165×930×1950

-

300

800

15

39.4

960

13

41.99

300WQ800-20-75

560

22.5

1450

51.2

75

1600

1110×700×1770

-

300

800

20

58.1

960

17

60.9

300WQ900-8-30

630

10

980

22.89

30

1150

1000×680×1860

-

300

900

8

23.22

1080

6.7

24.34

300WQ950-20-90

665

22.5

1450

60.2

90

1700

1110×700×1770

-

300

950

20

68.1

1140

17

70.4

300WQ950-24-110

665

27

1450

72

110

2000

1170×775×2100

-

300

950

24

81.8

1140

21

87

350WQ1000-36-160

700

40

980

112.2

160

1880

1670×1340×2600

-

350

1000

36

124.4

1200

31

131.6

350WQ1085-28-132

759.5

31.5

980

88.1

132

2520

1520×1300×2500

-

350

1085

28

99.7

1302

25

109.5

350WQ1100-10-45

770

11.5

980

32.6

45

1380

990×665×1876

-

350

1100

10

32.3

1320

8

35.1

350WQ1200-18-90

840

21

980

67.7

90

2000

1240×930×2140

-

350

1200

18

71.3

1440

15

73.6

350WQ1500-15-90

1050

17.5

980

70.5

90

2000

1280×930×2160

-

350

1500

15

74.8

1800

12

73.6

400WQ1500-26-160

1050

30

980

129

160

2880

1650×1300×2500

-

400

1500

26

129.6

1800

21

128.8

400WQ1700-22-160

1190

24

980

108.1

160

2880

2130×1260×2620

-

400

1700

22

122.8

2040

19

130.4

400WQ1700-30-200

1190

33

980

148.6

200

3850

1545×1240×2550

-

400

1700

30

167.4

2040

26

178.4

400WQ2200-15-132

1540

17.5

980

99.2

132

2520

1450×1240×2500

-

400

2200

15

105.8

2640

12

104

500WQ2000-15-110

1400

17.5

980

90.2

110

2100

1350×990×2500

-

500

2000

15

98.5

2400

12

96.9

500WQ2000-20-160

1400

22.5

980

119.2

160

2900

1520×1290×2550

-

500

2000

20

131.3

2400

17

137.3

500WQ2500-12-110

1750

13.7

980

88.3

110

2100

1580×1050×2200

-

500

2500

12

96.2

3000

9

89.7

500WQ2500-20-200

1750

22

980

141.8

200

3900

1665×1350×2600

-

500

2500

20

160.3

3000

17

169.5

 

FAQ

 

Standardized Project Inquiry Format for Engineering Procurement:

To enable our engineering applications team to issue a comprehensive technical proposal and formal quotation within 24 hours, please copy and complete the following project inquiry template when contacting our sales engineering desk:

  • Required Operating Flow Rate (Q): Please specify in cubic meters per hour (m³/h), liters per second (L/s), or US GPM.
  • Total Dynamic Head (H): Total static elevation difference plus calculated pipe friction and fitting head losses in meters (m) or feet (ft).
  • Pumped Fluid Characteristics: Fluid medium description, specific gravity, operating temperature (°C), pH range, and maximum suspended solid particle diameter (mm).
  • Electrical Grid Specifications: Supply voltage (e.g., 220V, 380V, 415V, 460V, 690V), frequency (50 Hz or 60 Hz), and number of phases (Three-Phase).
  • Preferred Installation Configuration: Auto-coupling guide rail lifting system (including upper bracket, guide rail pipes, and auto-coupling discharge foot) or Fixed standalone floor-mount.
  • Material & Coating Requirements: Standard HT200 cast iron, ductile iron QT500-7, cast 304/316/316L stainless steel, or special wear-resistant epoxy coatings.
  • Destination Port & Incoterms: Preferred delivery terms (FOB Chinese Port or CIF Destination Port Name) for accurate freight and transit scheduling.

 

news-800-798

 

 

Hot Tags: submersible wastewater pump, China submersible wastewater pump manufacturers, suppliers, factory

Send Inquiry